Octoprint: Difference between revisions
Line 1: | Line 1: | ||
= OctoPrint setup = | = OctoPrint setup = | ||
<li style="display: inline-block;"> [[File:Octoprint-600x400.png|thumb|100px|link=http://192.168.2.5/|Octoprint Creality Ender 3]] </li> | <li style="display: inline-block;"> [[File:Octoprint-600x400.png|thumb|100px|link=http://192.168.2.5/|Octoprint Creality Ender 3]] </li> | ||
<li style="display: inline-block;"> [[File:Octoprint-600x400.png|thumb|100px|link=http://192.168.2. | <li style="display: inline-block;"> [[File:Octoprint-600x400.png|thumb|100px|link=http://192.168.2.11/|Octoprint Creality CR6 SE]] </li> | ||
<li style="display: inline-block;"> [[File:Ps3-eye.jpg|thumb|100px|link=http://192.168.2.5/webcam/|Webcap Octoprint]] </li> | <li style="display: inline-block;"> [[File:Ps3-eye.jpg|thumb|100px|link=http://192.168.2.5/webcam/|Webcap Octoprint]] </li> | ||
Revision as of 12:28, 4 May 2021
OctoPrint setup
Base guide: https://community.octoprint.org/t/setting-up-octoprint-on-a-raspberry-pi-running-raspbian/2337
VM How to connect
- Open ssh session
- Create a virtual desktop using vncserver
<syntaxhighlight lang="Bash"> pi@raspberrypi:~ $ vncserver -geometry 1920x1080 </syntaxhighlight>
- Connect to the virtual desktop
<syntaxhighlight lang="Bash"> Address 192.168.2.5:1 <- :1 is the desktop number </syntaxhighlight>
- Kill the desktop when not needed
<syntaxhighlight lang="Bash"> pi@raspberrypi:~ $ vncserver -kill :1 </syntaxhighlight>
Serial install ch340
download
pi@raspberrypi:~ $ wget https://github.com/aperepel/raspberrypi ... 7/ch34x.ko
check
pi@raspberrypi:~ $ lsmod
Module Size Used by
bnep 12051 2
hci_uart 20020 1
btbcm 7916 1 hci_uart
bluetooth 365511 22 hci_uart,bnep,btbcm
brcmfmac 222874 0
brcmutil 9092 1 brcmfmac
cfg80211 543027 1 brcmfmac
rfkill 20851 4 bluetooth,cfg80211
snd_bcm2835 24427 1
snd_pcm 98501 1 snd_bcm2835
snd_timer 23968 1 snd_pcm
snd 70032 5 snd_timer,snd_bcm2835,snd_pcm
bcm2835_gpiomem 3940 0
evdev 12423 6
joydev 9988 0
uio_pdrv_genirq 3923 0
uio 10204 1 uio_pdrv_genirq
fixed 3285 0
i2c_dev 6913 0
fuse 99603 3
ipv6 408971 70
go towards
pi@raspberrypi:~ $ cd /lib/modules/$(uname -r)/kernel/drivers/usb/serial
Install first
pi@raspberrypi:/lib/modules/4.9.35-v7+/kernel/drivers/usb/serial $ sudo insmod usbserial.ko
Check once again
pi@raspberrypi:/lib/modules/4.9.35-v7+/kernel/drivers/usb/serial $ lsmod
Module Size Used by
usbserial 29943 0 <===== Need be installed FIRST
bnep 12051 2
hci_uart 20020 1
btbcm 7916 1 hci_uart
bluetooth 365511 22 hci_uart,bnep,btbcm
brcmfmac 222874 0
brcmutil 9092 1 brcmfmac
cfg80211 543027 1 brcmfmac
rfkill 20851 4 bluetooth,cfg80211
snd_bcm2835 24427 1
snd_pcm 98501 1 snd_bcm2835
snd_timer 23968 1 snd_pcm
snd 70032 5 snd_timer,snd_bcm2835,snd_pcm
bcm2835_gpiomem 3940 0
evdev 12423 6
joydev 9988 0
uio_pdrv_genirq 3923 0
uio 10204 1 uio_pdrv_genirq
fixed 3285 0
i2c_dev 6913 0
fuse 99603 3
ipv6 408971 68
NOW, install ch341.ko
pi@raspberrypi:/lib/modules/4.9.35-v7+/kernel/drivers/usb/serial $ sudo insmod ch341.ko
Voilá !!!
pi@raspberrypi:/lib/modules/4.9.35-v7+/kernel/drivers/usb/serial $ lsmod
Module Size Used by
ch341 6086 0 <==== Must be here first
usbserial 29943 1 ch341 <==== Can you see me now ?
bnep 12051 2
hci_uart 20020 1
btbcm 7916 1 hci_uart
bluetooth 365511 22 hci_uart,bnep,btbcm
brcmfmac 222874 0
brcmutil 9092 1 brcmfmac
cfg80211 543027 1 brcmfmac
rfkill 20851 4 bluetooth,cfg80211
snd_bcm2835 24427 1
snd_pcm 98501 1 snd_bcm2835
snd_timer 23968 1 snd_pcm
snd 70032 5 snd_timer,snd_bcm2835,snd_pcm
bcm2835_gpiomem 3940 0
evdev 12423 6
joydev 9988 0
uio_pdrv_genirq 3923 0
uio 10204 1 uio_pdrv_genirq
fixed 3285 0
i2c_dev 6913 0
fuse 99603 3
ipv6 408971 68
Hardware
Hardware | Picture | Link |
---|---|---|
Raspbery Pi | https://www.raspberrypi.org/downloads/raspbian/ | |
TFT | Configuration for the TFT | |
Camera 3EYE | Configuration for the 3EYE |